SAE 3340 carbon steel material

Specializes in SAE 3340 carbon steel material. With 20 years of experience in manufacturing steel products we offer high quality, lower cost but the best service. These SAE 3340 carbon steel material are available in different shape size and thickness according to the needs of our customer. SAE 3340 carbon steel material have excellent quality to fully satisfy customer’s requirements.

  • SAE steel grades

    The SAE steel grades system is a standard alloy numbering system for steel grades maintained by SAE International. In the 1930s and 1940s, the American Iron and Steel Institute (AISI) and SAE were both involved in efforts to standardize such a numbering system for steels. These efforts were similar and overlapped significantly.

  • SAE 4340 Carbon Steel Round Bar SNCM220 Bar ssroundbar

    Being one of the noted manufacturer, stockists and suppliers, weoffer SAE 4340 Carbon Steel Round Bar.Available at economical rates, the offered SAE 4340 Carbon Steel Round Bar are widely used in metallurgical, mechanical, electrical construction field, ships, military uses and automobile rear of products.We are a prominent name in manufacturing and supplying a wide range of SAE 4340 Carbon

  • SAE 4340 steel

    Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. SAE 4340 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

  • ASTM SAE AISI 1018 Carbon Steel Chemical Composition

    Below is material AISI 1018 carbon steel datasheet including chemical composition, density, thermal expansion coefficient, thermal conductivity, yield strength, hardness, etc. AISI SAE 1018 Chemical Composition. ASTM AISI SAE 1018 chemical composition is presented in the following table.

  • SAE/AISI Carbon & Alloy Steel Name System Otai Special Steel

    SAE steel 1018 indicates non modified carbon steel containing 0.18% of carbon. SAE steel 5130 indicates a chromium alloy steel containing 1% of chromium and 0.30% of carbon. An additional letter is sometimes added between the second and third digits of the

  • AISI/SAE Steel Numbering System Engineering ToolBox

    AISI/SAE steel numbers are indicated below. Example AISI/SAE No. 1020. the first digit indicates that this is plain carbon steel. the second digit indicates there are no alloying elements; the last two digits indicates that the steel contains approximately 0.20 percent carbon ; Example AISI/SAE No. 4340

  • SAE AISI 1018 Steel vs. SAE AISI 4340 Steel :

    Both SAE AISI 1018 steel and SAE AISI 4340 steel are iron alloys. They have a very high 97% of their average alloy composition in common. There are 31 material properties with values for both materials. Properties with values for just one material (1, in this case) are not shown.

  • SAE/AISI Carbon Steel Naming Conventions

    SAE 1018 indicates non modified carbon steel containing 0.18% of carbon. SAE 5130 indicates a chromium alloy steel containing 1% of chromium and 0.30% of carbon. An additional letter is sometimes added between the second and third digits of the code groups such as 11L41, 12L14 or 50B40.

  • SAE 4340 steel

    Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. SAE 4340 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

  • 1045 medium tensile carbon steel in AISI Standard

    Comparative MaterialsSome nearly matching materials are discussed belowAISI 1020AISI 1020 is a low carbon steel which shares features like easy machinability and high weldability with AISI 1045 steel. However it has lower carbon content which makes it less harder and it doesn’t support hardening processes either unlike AISI 1045.

  • Materials Medium Carbon Steel Bolts in SAE J429 (Grades

    Materials Medium Carbon Steel Bolts in SAE J429 (Grades 2, 5 and 8) Scope. SAE J429 is the standard specification for inch series steel bolts, screws, studs, SEMS screws and U bolts in sizes up to and including 1 1/2 inches. They are generally manufactured from variants of medium carbon steel. SAE J429 bolts from Glaser and Associates are

  • SAE AISI 1095 Steel, High Carbon Steel Heat Treat

    AISI 1095 Steel. SAE AISI 1095 steel is one of the most widely used 10 series steels, with good performance and low cost, with appropriate toughness and wear resistance, but poor corrosion resistance.. Applications. AISI SAE 1095 carbon steel can be made into steel billets, steel powder, which can be used as tool steel, blade steel, spring steel. 1095 high carbon steel uses mainly

  • Difference Between Low, Medium & High Carbon Steel The

    High quality low carbon steel is rolled into a thin plate to make deep drawn products such as automobile cabs and engine covers; it is also rolled into bars for the production of mechanical parts with low strength requirements. 2. Medium Carbon Steel. Medium carbon steel is a carbon steel with a carbon percentage content of 0.25% (or 0.29%) to

  • SAE AISI 1023 (G10230) Carbon Steel :MakeItFrom

    SAE AISI 1023 steel is a carbon (non alloy) steel formulated for primary forming into wrought products. 1023 is the designation in both the SAE and AISI systems for this material. G10230 is the UNS number. It has a fairly high thermal conductivity and a fairly low electrical conductivity among wrought carbon

  • AISI 1215 Carbon Steel (UNS G12150)

    AISI 1215 Carbon Steel (UNS G12150) Steel News Published on Thu, 04 Oct 2012 Carbon steels are designated by AISI four digit numbers. They contain carbon as the significant alloying element

  • AISI Carbon Steel Mechanical Characteristics Table Chart

    For all critical applications, verify to the applicable industry or requisite material / steel standard. AISI Carbon Steel Mechanical Characteristics Table Chart Yield, Tensile, Hardness AISI 3140 AISI 9310